Direkt Sensorkabel 100mm - CC011-0176-00 | CASTLE | Rynos.se

Din sida
Castle Direkt Sensorkabel 100mm i gruppen Elektronik / Fartreglage / Fartreglage tillbehör hos Rynosx4 Hobbyshop AB (CC011-0176-00)
CASTLE CREATIONS

Castle Direkt Sensorkabel 100mm

Artnr: CC011-0176-00
229 kr
 
Köp

Castle CC011-0176-00 - Direct Connect Sensor Wire 100mm

The Direct-Connect Sensor Wire eliminates the need for the Castle sensor harness adapter. This eliminates a connection point and makes your installation cleaner. One end has the standard ROAR sensor plug that connects to the back of any sensored motor. The other end plugs directly into any waterproof, sensor-capable Castle ESC.

Compatible ESCs:
  • Cobra 8
  • Cobra 10
  • Mamba Micro X
  • Mamba Micro X2
  • Mamba X
  • Mamba Monster X
  • Mamba Monster X 8s
  • Mamba XLX2
  • Copperhead 10

Available lengths:
  • 100mm
  • 150mm
  • 200mm
  • 250mm
  • 300mm
  • 400mm

INSTALLATION INSTRUCTIONS:
The Castle Creations Direct Sensor Wire helps clean up your wiring. It eliminates the need to use the Castle Sensor Harness that is included with Castle waterproof ESCs.

  • Compatible with all sensored brushless motors.
  • Compatible with all Castle waterproof sensored ESCs: Cobra series, Copperhead 10, Mamba Micro X/2, Mamba X, Mamba Monster X, Mamba Monster X 8s, and Mamba XLX2.
  • Available lengths: 100, 150, 200, 250, 300 & 400mm

Motor Installation:
Plug new direct connect sensor wire into the back of the motor. The plug is keyed so it will only insert correctly one way.

Mamba Micro X/2 and Copperhead 10 Installation:
  1. Unplug existing sensor harness (or dust cover) from ESC.
  2. - If removing dust cover, use pliers to grab center tab.
  3. Unplug receiver/fan harness from ESC.
  4. Plug in new direct connect sensor wire; mind the orientation by aligning the white wire to the corresponding whit dot on the side of the ESC.
  5. Plug in receiver/fan harness. Mind the orientation.

Mamba X Installation:
  1. Remove 2 screws beside capacitors, using 1.5mm hex.
  2. Remove C-shaped wire harness retainer.
  3. Unplug existing sensor harness from ESC.
  4. Plug in new direct connect sensor wire; mind the orientation by aligning the white wire to the corresponding whit dot on the side of the ESC.
  5. Reinstall wire harness retainer and screws.
Mamba Monster X and Monster X 8s Installation:
  1. Unplug existing sensor harness (or dust cover) from ESC.
    - Press against the slotted top case to allow easier removal; there is a lip that helps retain the sensor harness in place.
    - Pull the wires/plug of the harness slightly away from ESC and then up.
    - If removing dust cover, use pliers to grab center tab.
  • 2. Plug in new direct connect sensor wire; mind the orientation by aligning the white wire to the corresponding whit dot on the side of the ESC.
  • Insert harness at slight angle, just barely past the top case lip.
  • Rotate plug vertically once past the top case lip.
  • Make sure you are aligned properly and not missing a pin.
  • It is easy to accidentally miss all of the pins and the harness will slip behind them.
  • You can use a small flat head screw driver to fully seat the harness.
Visa mer
Visa mindre

Egenskaper

Passar till

Filer

Tillbehör

Delar

Recensioner

Tips & Tricks

Snabb leverans

Alla ordrar som läggs vardagar innan klockan 12.00 packas och skickas redan samma dag.

Hämta i butik

Få din beställning skickad eller hämta ut den i vår butik på Annelundsgatan 17 B i Enköping. 

Frågor?

Ring oss på 0171-305 80 (måndag-fredag 14-18 & lördagar 10-14) eller maila till service@rynos.se.

Fler populära produkter